“”

M6x1.00 to M18x1.50 Tap, Metric Coarse, Metric Fine, NPT, UNC, UNF, Tap and Die Set - Carbon Steel, Carbon Steel Taps, Adjustable, 110 Piece Set with Metal Case

24 Volts, DC, 37.5 CFM, Square Tube Axial Fan;0.13 Amp Rating, 2,700 to 3,000 RPM, 3.15" High x 3.15" Wide x 1" Deep

4" Max Seal, Table Top Thermal Impulse Sealer Repair Kit

28.5mm, 3MT 118° Point High Speed Steel Taper Shank Drill Bit - Oxide Finish, 175mm Flute Length, 296mm OAL, Spiral Flute

Radial/Deep Groove Ball Bearing - Straight Bore, 0.3750 in ID, 0.8750 in OD, 0.2812 in Width, Without Snap Ring

3/8-24 UNF Grade 8 Hex Lock Nut with Nylon Insert - 9/16" Width Across Flats, 15/32" High, Zinc Yellow Dichromate Finish

4 Piece, 2, 2-3/8, 3, 4 Inch Base Length, 2, 3, 4, 6 Inch Blade Length, Square Set Steel, Includes 4 Pc. Set of 2-6 Inches

1/8" Thick, Round Cross Section, Shore 70, -40 to 250°F Buna-N, also known as nitrile rubber (NBR), is made of a synthetic rubber that has anti-microbial properties and is resistant to chemicals, oils, solvents, greases and petroleum-based fluids. It is resistant to abrasions, cuts, punctures, slashes and snags.|Round cross-section shapes can be used in both static and dynamic applications. They are used as a mechanical seal or gasket and are seated in a groove and compressed during assembly between two or more parts.

Schedule 40, 1/4" Diam x 12" Long Steel Black Pipe Nipple; Threaded

1/2-13 UNC, 1" OAL, Knurled Cup Point Set Screw Grade 8 Alloy Steel, 1/4" Key

#10-32 UNF, 1/4" OAL, Knurled Cup Point Set Screw Grade 8 Alloy Steel, 3/32" Key

1/4-20, Electropolished Finish, Stainless Steel Wire Turned Closed Eye Bolt - 2" Thread Length, 15/32" ID x 29/32" OD, 3-19/32" Shank Length

6" Long Red Nylon Standard Cable Tie

1/4 x 1/4" Shank, Lead Angle Turning Single Point Tool Bit, BL-4, Grade C6

12" Max Seal, Table Top Thermal Impulse Sealer Repair Kit

5/8 x 5/8" Shank, Pointed Nose Single Point Tool Bit, D-10, Grade C6

3" Inside Diam x 3-3/4" Outside Diam Lip Seal - Standard 3/8" High, Polyurethane

0.0930 Inch Diameter, Lead Free Solid Wire Solder, 1 Lb., 13 Gauge

7 Piece 1/4-20 Steel Transfer Screw Set -

3/16" Oval Compression Sleeve - Aluminum

3/8" Compression Inlet, 1/2" FIP Outlet, Stainless Steel Lavatory/Sink Supply Line Use with Sinks

Size 4, 0.248" Large End Diam, Passivated Stainless Steel 1/4-28 Threaded Taper Pin - Grade 303, 18-8, 2 Pin Length

1" 316/316L Stainless Steel Pipe Tee FNPT x FNPT x FNPT Ends, 3,000 psi

250 VAC 20A NEMA L15-20 Industrial Twist Lock Connector;3 Poles, 4 Wires, 1 Phase, IP67, Ungrounded, Yellow